$135.31
The compression point is the first part to go through the ground and is attached...
$221.44
This point is actually 2-3/8" in diameter and will make a hole large enough to...
$285.00
This part is used to install 1-1/2"" galvanized rigid conduit GRC, after the initial hole...
$148.12
This part is used to insert a 1-1/2" PVC Sch 40 pipe into the ground...
$385.00
This connector is used to connect 1-1/2" poly pipe to the shafts before the shafts...
$185.00
This part is made of a very tough American-made steel, which is heat treated and...
$165.94
The compression point is the first part to go through the ground and is attached...
$61.60
The push cap is attached directly to the PVC pipe that is ready to be...
$116.84
This part is used to insert a 1-1/4" PVC Sch 40 pipe into the ground...
$102.23
This part is used to insert a 1-1/4" Sch 40 pipe into the ground after...
Sold Out
This connector is used to connect 1-1/4" poly pipe to the shafts before the shafts...
$98.00
This part is made of stainless steel and is used to insert 1/2"-1" "k" or...
$240.00
This part is made of stainless steel and is used to insert a - 2"...
$417.56
This particular point is the Largest point that we sell. It is actually 3" in diameter...
$285.00
This part is used to install 2" galvanized rigid conduit pipe, after the initial hole...
$285.00
This part is used to install 2" galvanized rigid conduit pipe, after the initial hole...
$265.17
This part is used to insert a 2" PVC Sch 40 pipe into the ground...
$335.00
After the pipe or conduit is installed over the shafts, this part is used to...
Sold Out
This connector is used to connect 2" poly pipe to the shafts before the shafts...
$2,738.94
This tool pack comes with everything you will need to go under any 16 foot...
$335.00
After the pipe or conduit is installed over the shafts, this part is used to...
$50.99
The push cap is attached directly to the PVC pipe that is ready to be...
$118.00
This connector is used to connect 1-1/4" poly pipe to the shafts before the shafts...
$117.69
This part is used to insert a 3/4' & 1" Sch 40 PVC pipe into...
$459.00
The quick shafts are used to connect to any number of other quick shafts in...
$500.00
The quick shafts are used to connect to any number of other quick shafts in...
$639.00
The 5 ft. master shaft is usually the first shaft to go into the ground...
$569.00
The quick shafts are used to connect to any number of other quick shafts in...
$10.00
Used to remove the screws in the cap of the metal case that houses the...
$95.00
A tough storage case that will hold 4 - 5'-4" Shafts. It has a bright...
$110.00
This nozzle can be used to moisten and remove soil from a smaller hole after...
$68.00
This Connector is used to connect direct buriel wire or small pex pipe to the...
$2,000.00
This rig is used to punch holes and install micro duct from the edge of...
$25.00
The digging bar hook is used to attach a grab hook to a digging. Once...
$285.00
Will hold up to 8 Shafts with a platform to display the Parts Case and...
$465.00
This part is used to pull in 2 -1 Inch PEX pipes at the same...
$134.38
Typically this part is not necessary but it can be very useful when going through...
$34.00
This is an extremely stiff and durable custom made brush that will clean the hardest...
$164.57
The impact cap slides into the female threaded end of all shafts (opposite the point...
$195.98
This part is used to connect the Bullet Mole to a jack hammer so that...
$72.00
This steel can be used with any jack hammer that requires a 1-1/8" hex shank....
$3,990.00 $4,290.00
Available 6-15-2024 This apparatus eliminates the need for a sledge hammer. Not only will it...
$10.00
Used to clean the male thread of our shafts and components that have male threads...
$90.00
These cases are metal with a stainless steel cap. They can hold up to 4...
$95.90
Designed to store a sidewalk kit, preassembled including the point, shaft and impact cap preassembled
