$2,738.94
This tool pack comes with everything you will need to go under any 16 foot...
$4,970.37
This tool pack comes with everything that you will need to go under any 21...
$940.61
Kit includes: (1) Quick shaft 1" Compression Point Impact Cap Pre assembled in a powder...
$3,990.00 $4,290.00
Available 6-15-2024 This apparatus eliminates the need for a sledge hammer. Not only will it...
$2,000.00
This rig is used to punch holes and install micro duct from the edge of...
$117.69
This part is used to insert a 3/4' & 1" Sch 40 PVC pipe into...
$135.31
The compression point is the first part to go through the ground and is attached...
$50.99
The push cap is attached directly to the PVC pipe that is ready to be...
$465.00
This part is used to pull in 2 -1 Inch PEX pipes at the same...
$165.94
The compression point is the first part to go through the ground and is attached...
$61.60
The push cap is attached directly to the PVC pipe that is ready to be...
$102.23
This part is used to insert a 1-1/4" Sch 40 pipe into the ground after...
$221.44
This point is actually 2-3/8" in diameter and will make a hole large enough to...
$148.12
This part is used to insert a 1-1/2" PVC Sch 40 pipe into the ground...
$417.56
This particular point is the Largest point that we sell. It is actually 3" in diameter...
$265.17
This part is used to insert a 2" PVC Sch 40 pipe into the ground...
$89.94
This pull connector is used to attach any 3/4" - 1" NPT(National Pipe Thread) Fitting...
$185.00
This part is made of a very tough American-made steel, which is heat treated and...
$285.00
This part is used to install 2" galvanized rigid conduit pipe, after the initial hole...
$285.00
This part is used to install 2" galvanized rigid conduit pipe, after the initial hole...
$285.00
This part is used to install 1-1/2"" galvanized rigid conduit GRC, after the initial hole...
$569.00
The quick shafts are used to connect to any number of other quick shafts in...
$639.00
The 5 ft. master shaft is usually the first shaft to go into the ground...
$500.00
The quick shafts are used to connect to any number of other quick shafts in...
$164.57
The impact cap slides into the female threaded end of all shafts (opposite the point...
$118.00
This connector is used to connect 1-1/4" poly pipe to the shafts before the shafts...
$89.94
This pull connector is used to attach any 3/4" - 1" NPT(National Pipe Thread) Fitting...
$68.00
This Connector is used to connect direct buriel wire or small pex pipe to the...
$465.00
This connector is used to connect 2" poly pipe to the shafts before the shafts...
$228.00
This connector is used to connect 1-1/4" poly pipe to the shafts before the shafts...
$465.00
This part is used to pull in 2 -1 Inch PEX pipes at the same...
$385.00
This connector is used to connect 1-1/2" poly pipe to the shafts before the shafts...
$109.54
This is used to support the shafts and hold them up off of the ground...
$195.98
This part is used to connect the Bullet Mole to a jack hammer so that...
$134.38
Typically this part is not necessary but it can be very useful when going through...
$25.00
The digging bar hook is used to attach a grab hook to a digging. Once...
$3,990.00 $4,290.00
Available 6-15-2024 This apparatus eliminates the need for a sledge hammer. Not only will it...
$2,000.00
This rig is used to punch holes and install micro duct from the edge of...
